STM32F207下的实验（3）

阳光穿透心脏的1/2处 2022-05-27 20:43 134阅读 0赞

1. DMA

2.Icapture

3. pwm

4. Time

1. DMA

led.h

#include"stm32f2xx.h"
    #ifndef __LED_H
    
    #define __LED_H
    
    void LED_Init(void);
    
    void Delay(vu32 nCount);
    
    void CTL_LED(u8 LED_NUM, u8 OFF_ON);
    
    	
    #endif

led.c

#include"led.h"
    #include"stm32f2xx.h"
    
    void LED_Init(void)
    {
    	GPIO_InitTypeDef GPIO_InitStructure;
    	
        //RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOF, ENABLE);
        RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
    		
    	//GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10;
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11|GPIO_Pin_12;
    	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
    	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //GPIO_OType_PP表示推挽方式输出，GPIO_OType_OD表示开漏
    	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
    	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    	
    	//GPIO_Init(GPIOF, &GPIO_InitStructure);
    	//GPIO_SetBits(GPIOF,GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10);
    	GPIO_Init(GPIOD, &GPIO_InitStructure);
    	GPIO_SetBits(GPIOD,GPIO_Pin_11|GPIO_Pin_12);
    }
    
    void Delay(vu32 nCount)
    {
      for(; nCount != 0; nCount--);
    }
    
    void CTL_LED(u8 LED_NUM, u8 OFF_ON)
    {
      switch(LED_NUM)
    	{
    	    case 0:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_11);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_11);
    			}
    		    break;
    		    
    		case 1:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_12);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_12);
    			}
    		    break;
    		    
    		//case 2:
    			//GPIO_ResetBits(GPIOF, GPIO_Pin_9);
    		   // break;
    		//case 3:
    			//GPIO_ResetBits(GPIOF, GPIO_Pin_10);
    		    //break;
    		default:
    			//GPIO_ResetBits(GPIOF,GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10);
    			GPIO_ResetBits(GPIOD,GPIO_Pin_11|GPIO_Pin_12);
    		    break;
    	}
    }

usart\_2.h

#include"stm32f2xx.h"
    #include "stdio.h"	
    #include "stm32f2xx_conf.h"
    #include"led.h"
    
    #ifndef __USART_2_H
    
    #define __USART_2_H
    
    void uart_init(u32 bound);
    //void USART1_IRQHandler(void);
    //void USART3_IRQHandler(void);
    
    
    #define USART_REC_LEN  			200  	//最大接收字节数 200
    //#define EN_USART1_RX 			1		//使能（1）/禁止（0）串口1接收
    #define EN_USART3_RX 			1		//使能（1）/禁止（0）串口3接收
    
    	  	
    extern u8  USART_RX_BUF[USART_REC_LEN]; //接收缓冲,最大USART_REC_LEN个字节.末字节为换行符 
    extern u16 USART_RX_STA;         		//接收状态标记	
    
    void uart_init(u32 bound);
    
    #endif

usart\_2.c

#include"stm32f2xx.h"
    #include"usart_2.h"
    #include"led.h"
    
    
    //初始化IO 串口3
    //bound:波特率
    
    void uart_init(u32 bound)
    {
    	GPIO_InitTypeDef  GPIO_InitStructure;//首先定义一个GPIO初始化结构体
    	USART_InitTypeDef USART_InitStructure;//定义一个串口初始化结构体
    //	NVIC_InitTypeDef NVIC_InitStructure; //定义中断初始化结构
    		
    	RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);//串口3是在APB1总线之下的，使能串口3的时钟,在rcc.h中
    	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE); //GPIO时钟使能
    	
        GPIO_PinAFConfig(GPIOB, GPIO_PinSource10, GPIO_AF_USART3); //引脚复用映射，在gpio.h文件，第三个参数表示映射到什么功能
        GPIO_PinAFConfig(GPIOB, GPIO_PinSource11, GPIO_AF_USART3);//表示将pinA9映射到串口3
    	
    	//GPIO端口初始化
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10|GPIO_Pin_11;
        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
        GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
        GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
        GPIO_Init(GPIOB, &GPIO_InitStructure);
    	
    	//端口初始化
    	USART_InitStructure.USART_BaudRate = bound;
    	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None; //硬件流控制
    	USART_InitStructure.USART_Mode = USART_Mode_Rx|USART_Mode_Tx;   //收发使能
    	USART_InitStructure.USART_Parity = USART_Parity_No;  
    	USART_InitStructure.USART_StopBits = USART_StopBits_1;
    	USART_InitStructure.USART_WordLength = USART_WordLength_8b; //8位字长
    	
    	USART_Init(USART3, &USART_InitStructure);//串口初始化
    	USART_Cmd(USART3, ENABLE); //串口使能函数
    	
    	USART_ITConfig(USART3, USART_IT_RXNE, ENABLE); //中断使能，第二个参数表示使能哪一种中断，USART_IT_RXNE表示接收非空，即接收到数据，就要产生中断
    
    }

dma.h

#include"stm32f2xx.h"
    #ifndef __DAM_H_
    #define __DAM_H_
    
    void DMA_Config(DMA_Stream_TypeDef* DMA_Streamx);
    
    void DMA_Enable(DMA_Stream_TypeDef* DMA_Streamx);
    
    #endif

dma.c

#include"dma.h"
    
    extern u8 SendBuff[8200];  //发送数据缓冲区
    
    void DMA_Config(DMA_Stream_TypeDef* DMA_Streamx)
    {
    	DMA_InitTypeDef DMA_InitStructure;
    	if((u32)DMA_Streamx > (u32)DMA2)
    	{
    		RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2, ENABLE);  //使能dma2时钟
    	}
    	else
    	{
    		RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA1, ENABLE);  //使能dma1时钟
    	}
    	
    	DMA_DeInit(DMA_Streamx);   //取消初始设置的DMA Streamx注册为默认复位值
    
    	DMA_InitStructure.DMA_Channel = DMA_Channel_4;   //通道
    	DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)&USART3->DR;  //外设基地址
    	DMA_InitStructure.DMA_Memory0BaseAddr = (u32)SendBuff;  //存储器基地址
    	DMA_InitStructure.DMA_DIR = DMA_DIR_MemoryToPeripheral;        //方向
    	DMA_InitStructure.DMA_BufferSize = 8200;   //传输量
    	DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;       //inc结尾，表示增量
    	DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
    	DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;    //数据长度
    	DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
    	DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;        //模式
    	DMA_InitStructure.DMA_Priority = DMA_Priority_Medium;     //优先级
    	DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable;       //fifo
    	DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_Full;
    	DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single; //突发单次传输
    	DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;        
    	DMA_Init(DMA_Streamx, &DMA_InitStructure);        //初始化dma通道参数
    }
    
    void DMA_Enable(DMA_Stream_TypeDef* DMA_Streamx)
    {
    	DMA_Cmd(DMA_Streamx, DISABLE);		   //使能dma1通道，启动传输
    
    	while(DMA_GetCmdStatus(DMA_Streamx) != DISABLE)   //查询dma的en位，确保数据流动续，可以配置
    	{}
    
    	DMA_SetCurrDataCounter(DMA_Streamx, 8200);    //设置通道当前剩余数据量
    
        DMA_Cmd(DMA_Streamx, ENABLE);		   //使能dma1通道，启动传输
    }

main.c

#include"stm32f2xx.h"
    #include"led.h"
    #include"dma.h"
    #include"usart_2.h"
    #if 1
    #define SEND_BUF_SIZE 8200
    
    u8 SendBuff[SEND_BUF_SIZE];  //发送数据缓冲区
    const u8 TEXT_TO_SEND[];
    
    int main(void)
    { 
    	//float pro = 0;    //进度
    	u16 i;
    	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);//设置系统中断优先级分组2
    	Delay(168);		    //延时初始化 
    	uart_init(115200);	//串口初始化波特率为115200
    	LED_Init();		  	//初始化与LED连接的硬件接口
    
    	DMA_Config(DMA1_Stream3);
    
    	for(i = 0; i < SEND_BUF_SIZE; i++)
    	{
    		SendBuff[i] = 1;
    	}
    	
    	USART_DMACmd(USART3, USART_DMAReq_Tx, ENABLE);    //使能串口dma发送
    	//DMA_Enable(DMA1_Stream3);
    	DMA_Cmd(DMA1_Stream3, ENABLE);	
    	
    	while(1)
    	{
    		//TCIFx表示数据流x传输完成中断标志，中文参考p221
    		if(DMA_GetFlagStatus(DMA1_Stream3, DMA_FLAG_TCIF3) != RESET)    //查询dma传输状态，TCIF后的系数与stream后的系数保持一致
    		{
    			DMA_ClearFlag(DMA1_Stream3, DMA_FLAG_TCIF3);
    			break;
    		}
    		//pro = DMA_GetCurrDataCounter(DMA1_Stream3);    //获取、设置通道当前剩余数据量
    		//pro = 1-pro/SEND_BUF_SIZE;//	  
    		//pro*=100;      			    //得到百分比
    		//while(pro == 100)
    		//{
    		//	CTL_LED(0, 1);
    		//}
    		
    		CTL_LED(1, 1);	
    		Delay(10000000);
    		//CTL_LED(0, 1);
    	}	
    	
    }
    #endif

2. Icapture

usart\_2.h

usart\_2.c

#include"stm32f2xx.h"
    #include"usart_2.h"
    #include"led.h"
    
    
    //初始化IO 串口3
    //bound:波特率
    
    #if 1
    #pragma import(__use_no_semihosting)             
    //±ê×??aDèòaμ??§3?oˉêy                 
    struct __FILE 
    { 
    	int handle; 
    }; 
    
    FILE __stdout;       
    //   
    _sys_exit(int x) 
    { 
    	x = x; 
    } 
    
    int fputc(int ch, FILE *f)
    { 	
    	while((USART3->SR&0X40)==0);
    	USART3->DR = (u8) ch;      
    	return ch;
    }
    #endif
    
    void uart_init(u32 bound)
    {
    	GPIO_InitTypeDef  GPIO_InitStructure;//首先定义一个GPIO初始化结构体
    	USART_InitTypeDef USART_InitStructure;//定义一个串口初始化结构体
    		
    	RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);//串口3是在APB1总线之下的，使能串口3的时钟,在rcc.h中
    	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE); //GPIO时钟使能
    	
        GPIO_PinAFConfig(GPIOB, GPIO_PinSource10, GPIO_AF_USART3); //引脚复用映射，在gpio.h文件，第三个参数表示映射到什么功能
        GPIO_PinAFConfig(GPIOB, GPIO_PinSource11, GPIO_AF_USART3);//表示将pinA9映射到串口3
    	
    	//GPIO端口初始化
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10|GPIO_Pin_11;
        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
        GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
        GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
        GPIO_Init(GPIOB, &GPIO_InitStructure);
    	
    	//端口初始化
    	USART_InitStructure.USART_BaudRate = bound;
    	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None; //硬件流控制
    	USART_InitStructure.USART_Mode = USART_Mode_Rx|USART_Mode_Tx;   //收发使能
    	USART_InitStructure.USART_Parity = USART_Parity_No;  
    	USART_InitStructure.USART_StopBits = USART_StopBits_1;
    	USART_InitStructure.USART_WordLength = USART_WordLength_8b; //8位字长
    	
    	USART_Init(USART3, &USART_InitStructure);//串口初始化
    	USART_Cmd(USART3, ENABLE); //串口使能函数
    	
    	USART_ITConfig(USART3, USART_IT_RXNE, ENABLE); //中断使能，第二个参数表示使能哪一种中断，USART_IT_RXNE表示接收非空，即接收到数据，就要产生中断
    
    }

Icapture.h

#include"stm32f2xx.h"
    #ifndef __PWM_H_
    #define __PWM_H_
    
    void TIM9_CH1_Cap_Init(u32 arr, u32 psc);
    
    void TIM1_BRK_TIM9_IRQHandler(void);
    
    
    #endif

Icapture.c

#include"stm32f2xx.h"
    #include"Icapture.h"
    
    u8  TIM9CH1_CAPTURE_STA = 0;	//输入捕获状态，0表示还没有捕获到上升沿中断
    u32	TIM9CH1_CAPTURE_VAL;	   //输入捕获值(TIM9是32位还是16位)
    
    void TIM9_CH1_Cap_Init(u32 arr, u32 psc)  
    {
    	GPIO_InitTypeDef GPIO_InitStructure;
    	TIM_ICInitTypeDef TIM_ICInitStructure;
    	TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStructure;
    	NVIC_InitTypeDef NVIC_InitStructure;
    	
    	RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM9, ENABLE);   
    	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOE, ENABLE);
    
    	//初始化io口
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
    	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
    	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //GPIO_OType_PP表示推挽方式输出，GPIO_OType_OD表示开漏
    	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
    	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    	GPIO_Init(GPIOE, &GPIO_InitStructure);
    	
    	GPIO_PinAFConfig(GPIOE, GPIO_PinSource5, GPIO_AF_TIM9);  //设置引脚复用映射，将GPIOE5复用为TIM9
    
    	//初始化TIM9
    	TIM_TimeBaseInitStructure.TIM_Period = arr;    //自动装载值
    	TIM_TimeBaseInitStructure.TIM_Prescaler = psc;	//预分频系数
    	TIM_TimeBaseInitStructure.TIM_CounterMode = TIM_CounterMode_Up; //计数器模式
    	TIM_TimeBaseInitStructure.TIM_ClockDivision = TIM_CKD_DIV1;  //分频器系数
    	TIM_TimeBaseInit(TIM9, &TIM_TimeBaseInitStructure);
    
     	//输入捕获通道初始化函数
    	TIM_ICInitStructure.TIM_Channel = TIM_Channel_1;     //捕获通道
    	TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising;    //捕获极性
    	TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;    //映射关系
    	TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;    //分频系数
    	TIM_ICInitStructure.TIM_ICFilter = 0x00;    //滤波器
    	TIM_ICInit(TIM9, &TIM_ICInitStructure);
    
    	TIM_ITConfig(TIM9, TIM_IT_Update|TIM_IT_CC1, ENABLE);   //开启捕获中断和更新中断
    	
    	TIM_Cmd(TIM9, ENABLE);  //使能定时器TIM9
    	
    	NVIC_InitStructure.NVIC_IRQChannel = TIM1_BRK_TIM9_IRQn; //XTI9_5_IRQn;  8和14共用TIM8_TRG_COM_TIM14_IRQn
    	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
    	NVIC_InitStructure.NVIC_IRQChannelSubPriority =0;		
    	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;			
    	NVIC_Init(&NVIC_InitStructure);	
    	
    	//TIM_OC1PreloadConfig(TIM9, TIM_OCPreload_Enable);	//使能输出比较预装载，使能tim14在ccr1上的预装载寄存器
    	//TIM_ARRPreloadConfig(TIM9, ENABLE);	// 使能自动重装载的预装载寄存器的允许位， ARPE使能
    }
    
    void TIM1_BRK_TIM9_IRQHandler(void)     //中断服务函数，在启动文件中
    { 
    	if((TIM9CH1_CAPTURE_STA&0x80) == 0)    //TIM9CH1_CAPTURE_STA的第八位为0，还未成功捕获
    	{
    		if(TIM_GetITStatus(TIM9, TIM_IT_Update) != RESET)    //溢出，检查TIM9的更新中断是否产生，RESET=0
    		{
    			if(TIM9CH1_CAPTURE_STA&0x40)      //已经捕获到高电平
    			{
    				if((TIM9CH1_CAPTURE_STA&0X3F) == 0X3F)  //高电平较长
    				{
    					TIM9CH1_CAPTURE_STA|=0X80;		// 标记成功地捕获了一次
    					TIM9CH1_CAPTURE_VAL = 0XFFFFFFFF;    //32个1
    				}
    				else 
    					TIM9CH1_CAPTURE_STA++;
    			}
    		}
    
    		if(TIM_GetITStatus(TIM9, TIM_IT_CC1) != RESET)//检查TIM9的捕获中断是否发生
    		{	
    			if(TIM9CH1_CAPTURE_STA&0X40)		//	已经捕获到下降沿	
    			{	  			
    				TIM9CH1_CAPTURE_STA|=0X80;		//标记成功地捕获了一次高电平脉宽
    			    TIM9CH1_CAPTURE_VAL = TIM_GetCapture1(TIM9);//获取当前的捕获值
    	 			TIM_OC1PolarityConfig(TIM9, TIM_ICPolarity_Rising); //cc1p = 0， 设置为上升沿捕获
    			}
    			else  								//TIM9CH1_CAPTURE_STA的第6位为0，则还没有捕获到新的上升沿，先将下面几个值清0
    			{
    				TIM9CH1_CAPTURE_STA = 0;			//清空
    				TIM9CH1_CAPTURE_VAL = 0;
    				TIM9CH1_CAPTURE_STA|=0X40;		//设置TIM9CH1_CAPTURE_STA的第6位为1，标记捕获到了上升沿
    				//TIM_Cmd(TIM9, DISABLE ); 	//关闭定时器9
    	 			TIM_SetCounter(TIM9, 0);     //定时器计数值清0
    	 			TIM_OC1PolarityConfig(TIM9, TIM_ICPolarity_Falling);  //通道极性设置独立函数，cc1p = 1， 设置为下降沿捕获，等待下降沿到来,low = falling
    				TIM_Cmd(TIM9, ENABLE ); 	//使能定时器9
    			}		    
    	    }
    	}
    	TIM_ClearITPendingBit(TIM9, TIM_IT_CC1|TIM_IT_Update);    //清空中断和捕获标志位
    }

main.c

#include"stm32f2xx.h"
    #include"usart_2.h"
    //#include"led.h"
    #include"Icapture.h"
    
    extern u8  TIM9CH1_CAPTURE_STA;	
    extern u32	TIM9CH1_CAPTURE_VAL;	
    
    int main(void)
    { 
    	long long temp = 0;  
    	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
    	Delay(168);		    
    	//LED_Init();		  	
    	uart_init(115200);
    	
    	TIM9_CH1_Cap_Init(0XFFFFFFFF, 84-1);  //arr的值是32个1，足够大
    	
    	while(1)
    	{
     		Delay(10);			 
     		if(TIM9CH1_CAPTURE_STA&0X80)        //最高位为1，表示捕获完成
    		{
    			temp = TIM9CH1_CAPTURE_STA&0X3F;   //temp表示捕获高电平定时器溢出的次数
    			temp*=0XFFFFFFFF;		 		         //溢出次数与arr的乘积
    			temp+=TIM9CH1_CAPTURE_VAL;		   //时间长度内，cnt计数的次数
    			printf("HIGH:%lld us\r\n", temp); //
    			TIM9CH1_CAPTURE_STA = 0;			     //TIM9CH1_CAPTURE_STA置0，就可以开启第二次捕获
    		}
    	}
    }

3. pwm

led.h

#include"stm32f2xx.h"
    #ifndef __LED_H
    
    #define __LED_H
    
    
    void LED_Init(void);
    
    void Delay(vu32 nCount);
    
    void CTL_LED(u8 LED_NUM, u8 OFF_ON);
    
    	
    #endif

led.c

#include"led.h"
    #include"stm32f2xx.h"
    
    void LED_Init(void)
    {
    	GPIO_InitTypeDef GPIO_InitStructure;
    	
        RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;
    	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
    	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //GPIO_OType_PP表示推挽方式输出，GPIO_OType_OD表示开漏
    	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
    	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    
    	GPIO_Init(GPIOD, &GPIO_InitStructure);
    	GPIO_SetBits(GPIOD, GPIO_Pin_12);
    }
    
    
    void Delay(vu32 nCount)
    {
      for(; nCount != 0; nCount--);
    }
    
    #if 0
    void CTL_LED(u8 LED_NUM, u8 OFF_ON)
    {
      switch(LED_NUM)
    	{
    	    case 0:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_11);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_11);
    			}
    		    break;
    		    
    		case 1:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_12);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_12);
    			}
    		    break;
    		default:
    			//GPIO_ResetBits(GPIOF,GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10);
    			GPIO_ResetBits(GPIOD,GPIO_Pin_11|GPIO_Pin_12);
    		    break;
    	}
    }
    #endif

pwm.h

#include"stm32f2xx.h"
    #ifndef __PWM_H_
    #define __PWM_H_
    
    void TIM4_PWM_Init(u32 arr, u32 psc);
    
    
    #endif

pwm.c

#include"stm32f2xx.h"
    #include"pwm.h"
    
    void TIM4_PWM_Init(u32 arr, u32 psc)
    {
    	GPIO_InitTypeDef GPIO_InitStructure;
    	TIM_OCInitTypeDef TIM_OCInitStructure;
    	TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStructure;
    	
    	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE);   //使能定时器4时钟
    	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);   //使能gpio时钟
    
    	GPIO_PinAFConfig(GPIOD, GPIO_PinSource12, GPIO_AF_TIM4);  //将GPIOD12复用为TIM4
    	
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;
    	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
    	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //GPIO_OType_PP表示推挽方式输出，GPIO_OType_OD表示开漏
    	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
    	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    	GPIO_Init(GPIOD, &GPIO_InitStructure);
    	
    
    	//初始化TIM4  输出通道  初始化输出比较参数
    	TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;    //模式1决定，当cnt<ccr1时，通道1为有效电平
    	TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;  //输出使能
    	TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;  //极性，有效电平是高电平还是低电平
    	TIM_OC1Init(TIM4, &TIM_OCInitStructure);
    
    	//初始化TIM4初始化 pwm模式
    	TIM_TimeBaseInitStructure.TIM_Period = arr;    //自动装载值
    	TIM_TimeBaseInitStructure.TIM_Prescaler = psc;  //预分频系数
    	TIM_TimeBaseInitStructure.TIM_CounterMode = TIM_CounterMode_Up; //计数器模式
    	TIM_TimeBaseInitStructure.TIM_ClockDivision = TIM_CKD_DIV1;  //分频器系数
    	TIM_TimeBaseInit(TIM4, &TIM_TimeBaseInitStructure);
    	
        TIM_Cmd(TIM4, ENABLE);  //使能TIM14
    
    	TIM_OC1PreloadConfig(TIM4, TIM_OCPreload_Enable);  //使能输出比较预装载，使能tim14在ccr1上的预装载寄存器
    	TIM_ARRPreloadConfig(TIM4, ENABLE);    // 使能自动重装载的预装载寄存器的允许位， ARPE使能
    	
    }

main.c

#include"stm32f2xx.h"
    #include"led.h"
    #include"pwm.h"
    
    int main(void)
    { 
    	u16 ledpwmval = 0;   //ledpwmval是TIM_pulse
    	u8 dir = 1;         //dir值控制方向
    	LED_Init();		  	//初始化与LED连接的硬件接口
    
    	TIM4_PWM_Init(499, 29);    //29是预分频系数，则定时器计数频率是30/29+1=1um，周期由arr决定，重转载值是500，则由1和500，可知整个周期是500
    	TIM_SetCompare1(TIM4, 50);   //程序中频率可变的led灯实验不明显，这里设置为占空比为50%的，可通过示波器查看效果
    	
    	
    	while(1)
    	{	
    #if 0
    
    		Delay(20);
    		if(dir)
    		{
    			ledpwmval++;
    		}
    		else
    		{
    			ledpwmval--;
    		}
    
    		if(ledpwmval > 300)    //dir值控制方向
    		{ 
    			dir = 0;
    		}
    		else if(ledpwmval == 0)
    		{
    			dir = 1;
    		}
    		
    		TIM_SetCompare1(TIM4, ledpwmval);   //设置比较值函数，ledpwmval是变量，则不断改变占空比，从而led灯亮度变化
    #endif
    	}
    
    }

4. Time

led.h

led.c

#include"led.h"
    #include"stm32f2xx.h"
    
    void LED_Init(void)
    {
    	GPIO_InitTypeDef GPIO_InitStructure;
    	
        RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11|GPIO_Pin_12;
    	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
    	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //GPIO_OType_PP表示推挽方式输出，GPIO_OType_OD表示开漏
    	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
    	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    
    	GPIO_Init(GPIOD, &GPIO_InitStructure);
    	GPIO_SetBits(GPIOD,GPIO_Pin_11|GPIO_Pin_12);
    }
    
    void Delay(vu32 nCount)
    {
      for(; nCount != 0; nCount--);
    }
    
    void CTL_LED(u8 LED_NUM, u8 OFF_ON)
    {
      switch(LED_NUM)
    	{
    	    case 0:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_11);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_11);
    			}
    		    break;
    		    
    		case 1:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_12);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_12);
    			}
    		    break;
    		default:
    			//GPIO_ResetBits(GPIOF,GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10);
    			GPIO_ResetBits(GPIOD,GPIO_Pin_11|GPIO_Pin_12);
    		    break;
    	}
    }

time.h

#include"stm32f2xx.h"
    #ifndef __TIME_H_
    #define __TIME_H_
    
    void TIM3_Int_Init(u32 arr, u32 psc);
    
    void TIM3_IRQHandler(void);
    
    
    #endif

time.c

#include"stm32f2xx.h"
    #include"time.h"
    #include"led.h"
    
    void TIM3_Int_Init(u32 arr, u32 psc)
    {
    	TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStructure;
    	NVIC_InitTypeDef NVIC_InitStructure;
    	
    	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);  //使能定时器时钟
    
    	TIM_TimeBaseInitStructure.TIM_Period = arr;    //自动装载值
    	TIM_TimeBaseInitStructure.TIM_Prescaler = psc;  //预分频系数
    	TIM_TimeBaseInitStructure.TIM_CounterMode = TIM_CounterMode_Up; //计数器模式
    	TIM_TimeBaseInitStructure.TIM_ClockDivision = TIM_CKD_DIV1;  //分频器系数
    	TIM_TimeBaseInit(TIM3, &TIM_TimeBaseInitStructure);
    
    	TIM_ITConfig(TIM3, TIM_IT_Update, ENABLE);
    	
    	TIM_Cmd(TIM3, ENABLE);
    
    	//初始化中断函数
    	NVIC_InitStructure.NVIC_IRQChannel= TIM3_IRQn;  //xx.h
    	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;  
    	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x01;  
    	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x03;  
    	NVIC_Init(&NVIC_InitStructure);   	
    }
    
    void TIM3_IRQHandler(void)  //中断服务函数，在启动文件中
    {
    	if(TIM_GetITStatus(TIM3, TIM_IT_Update) != RESET)   //确定中断为更新中断
    	{
    		CTL_LED(0, 1);
    	}
    	TIM_ClearITPendingBit(TIM3, TIM_IT_Update);	
    }

main.c

#include"stm32f2xx.h"
    #include"led.h"
    #include"time.h"
    
    int main(void)
    { 
    	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);//设置系统中断优先级分组2
    	Delay(168);		    //延时初始化 
    	LED_Init();		  	//初始化与LED连接的硬件接口
    
    	TIM3_Int_Init(49999, 8399);
    
    	while(1)
    	{
    		CTL_LED(1, 1);	
    		Delay(200);
    	}
    }