STM32F207下的实验（1）- CAN通信基础

红太狼 2022-05-28 04:24 318阅读 0赞

CAN控制器通过两根线上的电位差来判断总线电平

can.h

#can.h
    
    #include"stm32f2xx.h" 
    
    #ifndef __CAN_H_
    #define __CAN_H_
    
    void CAN_Mode_Config(u8 CAN_BS1_xtq, u8 CAN_BS2_ytq, u16 Prescaler);
    
    u8 CAN_Send_Msg(u8 *msg, u8 len);
    
    u8 CAN_Receive_Msg(u8 *buf); 
    
    #endif

can.c

#include"stm32f2xx.h"
    #include"stm32f2xx_can.h"
    #include"can.h" 
    
    void CAN_Mode_Config(u8 CAN_BS1_xtq, u8 CAN_BS2_ytq, u16 Prescaler)
    {
    	GPIO_InitTypeDef  GPIO_InitStructure;
    	CAN_InitTypeDef CAN_InitStructure;
    	CAN_FilterInitTypeDef CAN_FilterInitStructure;
    	NVIC_InitTypeDef NVIC_InitStructure;
    
    	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);  //使能AHB1外设时钟
    	RCC_APB1PeriphClockCmd(RCC_APB1Periph_CAN1, ENABLE);  //使能CAN1时钟
    
    	//GPIO初始化
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1;
        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
        GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; 
        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
        GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
        GPIO_Init(GPIOD, &GPIO_InitStructure);
    
        GPIO_PinAFConfig(GPIOD, GPIO_PinSource0, GPIO_AF_CAN1); 
    	GPIO_PinAFConfig(GPIOD, GPIO_PinSource1, GPIO_AF_CAN1);
    	
        
    	//CAN初始化
    	CAN_InitStructure.CAN_ABOM = DISABLE;   	//软件自动离线管理	
    	CAN_InitStructure.CAN_AWUM = DISABLE;   //睡眠模式通过软件唤醒(清除CAN->MCR的SLEEP位)
    	CAN_InitStructure.CAN_BS1 = CAN_BS1_xtq;   //时间段1的时间单元，取值在CAN_BS1_1tq~CAN_BS1_16tq
    	CAN_InitStructure.CAN_BS2 = CAN_BS2_ytq;    //时间段2的时间单元，取值在CAN_BS2_1tq~CAN_BS2_8tq
    	CAN_InitStructure.CAN_Mode = CAN_Mode_Normal;    //模式设置，普通模式
    	CAN_InitStructure.CAN_NART = ENABLE;      //禁止报文自动传送 
    	CAN_InitStructure.CAN_Prescaler = Prescaler;         //分频系数(Fdiv)为brp+1	
    	CAN_InitStructure.CAN_RFLM = DISABLE;      //报文不锁定,新的覆盖旧的  
    	CAN_InitStructure.CAN_SJW = CAN_SJW_1tq;    //重新同步跳跃时间单元，CAN_SJW_1tq~CAN_SJW_4tq
    	CAN_InitStructure.CAN_TTCM = DISABLE;    //非时间触发通信模式 
    	CAN_InitStructure.CAN_TXFP = DISABLE;     //优先级由报文标识符决定 
    	CAN_Init(CAN1, &CAN_InitStructure);
    
    	//筛选初始化
    	CAN_FilterInitStructure.CAN_FilterActivation = ENABLE;    激活过滤器0
    	CAN_FilterInitStructure.CAN_FilterFIFOAssignment = CAN_FilterFIFO0;    //过滤器0关联到FIFO0
    	CAN_FilterInitStructure.CAN_FilterIdHigh = 0x0000;    //32位ID
    	CAN_FilterInitStructure.CAN_FilterIdLow = 0x0000;
    	CAN_FilterInitStructure.CAN_FilterMaskIdHigh = 0x0000;   //32位MASK
    	CAN_FilterInitStructure.CAN_FilterMaskIdLow = 0x0000;
    	CAN_FilterInitStructure.CAN_FilterMode = CAN_FilterMode_IdMask;    //屏蔽模式
    	CAN_FilterInitStructure.CAN_FilterNumber = 0;    //过滤器0
    	CAN_FilterInitStructure.CAN_FilterScale = CAN_FilterScale_32bit;    //
    	CAN_FilterInit(&CAN_FilterInitStructure);	
    
    	CAN_ITConfig(CAN1, CAN_IT_FMP0, ENABLE);   //fifo0的中断
    	NVIC_InitStructure.NVIC_IRQChannel = CAN1_TX_IRQn;  //stm..xx.h，发送中断
    	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; 
    	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x01;
    	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x01;
    	NVIC_Init(&NVIC_InitStructure);
    }
    
    //开始发送 
    u8 CAN_Send_Msg(u8 *msg, u8 len)     //msg为数据，len为长度
    {
    	u8 mbox;   //邮箱
    	u16 i = 0; 
    	
    	CanTxMsg TXmessage;    //can发送结构体
    		
    	TXmessage.DLC = len;  //数据个数，不能超过8个
    	TXmessage.ExtId = 0x12;    //扩展标示符
    	TXmessage.IDE = CAN_ID_STD;     //帧类型是标准帧，与这里的标准标示符和扩展标示符无关
    	//TXmessage.IDE = CAN_ID_EXT;   //这里的帧类型也可以设置为扩展帧，在USB_CAN那里设置标准帧，传输记录中会有
    	TXmessage.RTR = CAN_RTR_DATA;   //...can.h，传送的是数据帧
    	TXmessage.StdId = 0x12;  //标准标示符
    		
    	for(i = 0; i < len; i++)
    	{
    		TXmessage.Data[i] = msg[i];
    	}
    	
    	mbox = CAN_Transmit(CAN1, &TXmessage);  //返回当前邮箱
    
    	while((CAN_TransmitStatus(CAN1, mbox) == CAN_TxStatus_Failed)&&(i < 0xFFF))
    	{
    		i++;      //等待发送结束完成
    	}
    	if(i >= 0xFFF)
    	{
    		return 1;  
    	}	
    	return 0;
    }
    
    
    
    u8 CAN_Receive_Msg(u8 *buf)
    {
    	CanRxMsg RXmessage; 	//can接收结构体
    	u16 i = 0;
    
    	while(CAN_MessagePending(CAN1, CAN_FIFO0) == 0)     //查询接收状态位，看是否由信息(报文)到达
    	{
    		return 0;           //没有接收到数据，直接退出，看CAN_FIFO0中是否有数据
    	}
    	CAN_Receive(CAN1, CAN_FIFO0, &RXmessage);   //接收信息(报文)，将CAN_FIFO0中的数据通过can1拷贝到RXmessage结构体中
    	
    	for(i = 0; i < RXmessage.DLC; i++)
    	{
    		buf[i] = RXmessage.Data[i];
    	}
    
    	return RXmessage.DLC; 
    }

led.h

#include"stm32f2xx.h"
    
    #ifndef __LED_H
    
    #define __LED_H
    
    
    void LED_Init(void);
    
    void Delay(vu32 nCount);
    
    void CTL_LED(u8 LED_NUM, u8 OFF_ON);
    
    	
    #endif

led.c

#include"led.h"
    #include"stm32f2xx.h"
    
    void LED_Init(void)
    {
    	GPIO_InitTypeDef GPIO_InitStructure;
    	
        RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
    	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12|GPIO_Pin_11;
    	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;   //led灯做输出，不用复用
    	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; //GPIO_OType_PP表示推挽方式输出，GPIO_OType_OD表示开漏
    	GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
    	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    
    	GPIO_Init(GPIOD, &GPIO_InitStructure);
    	GPIO_SetBits(GPIOD, GPIO_Pin_12|GPIO_Pin_11);
    }
    
    
    void Delay(vu32 nCount)
    {
      for(; nCount != 0; nCount--);
    }
    
    #if 1
    void CTL_LED(u8 LED_NUM, u8 OFF_ON)
    {
      switch(LED_NUM)
    	{
    	    case 0:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_11);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_11);
    			}
    		    break;
    		    
    		case 1:
    			if(OFF_ON == 1)
    			{
    
    				GPIO_ResetBits(GPIOD, GPIO_Pin_12);
    			}
    			else
    			{
    				GPIO_SetBits(GPIOD, GPIO_Pin_12);
    			}
    		    break;
    		default:
    			//GPIO_ResetBits(GPIOF,GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10);
    			GPIO_SetBits(GPIOD,GPIO_Pin_11|GPIO_Pin_12);
    		    break;
    	}
    }
    #endif

main.c

#include"stm32f2xx.h"
    #include"can.h"
    #include"led.h"
    
    
    int main(void)
    {
    	u8 res;
    	u8 key;
    	
    	u8 canbuf[8] = {0};    //这里因为不知道从USB_CAN发的是什么，只需初始化为0即可
    	u8 a[8] = {02, 02, 02, 02, 02, 02, 02, 02};   //这里的02和2一样，12是0c
    
    	LED_Init();
    	Delay(168);
    
    	CAN_Mode_Config(CAN_BS1_8tq, CAN_BS2_6tq, 8);   //此时CAN波特率为：30000/(1+8+6)*8 = 250kbps
    
    	while(1)
     	{	
        	//1.接收数据
        	key = CAN_Receive_Msg(canbuf);
    
    		//2.解析数据
    		if(key == 0)
    		{
    			CTL_LED(1, 0);   //开始的时候，没有接收到数据，故左边灯亮
    		}
    		else if(key > 0)     //当接收到数据时，开始执行这一步
    		{ 
    		    //3.发送数据给PC
    		    CTL_LED(1, 1);   
    			res = CAN_Send_Msg(a, 8);    
    			if(res == 0)
    			{
    				CTL_LED(0, 1);   //若数据发送成功，点亮led灯0
    			}
    			else 
    			{
    				CTL_LED(1, 0);     //若数据发送失败，熄灭led灯1
    				 
    			}
    		}	
    	}
    
    //开始的时候，没有接收到数据，故左边灯亮，当接收到数据时，开始执行发送数据函数，若发送成功，右边灯亮，
    //若数据发送失败，熄灭led灯1
    //问题:数据发送成功和失败的判断:是否合理?左边的灯会一直亮
    //结合上面程序，将没有接收到数据时灯灭，数据发送时灯亮，可知数据发送成功，
    //问题:can程序实验代码不显示接收?而且和发送数据框的数据无关?
    /*
    	while(1)
    	{
    		res = CAN_Send_Msg(a, 8);
    		if(res == 0)
    		{
    			CTL_LED(0, 1);   //若数据发送成功，点亮led灯0，即右边灯
    			key = CAN_Receive_Msg(canbuf);
    			if(key == 0)
    			{
    				CTL_LED(1, 1);   //实验结果是，执行这一步 
    			}
    			else if(key > 0)
    			{
    				Delay(5000);
    				//CTL_LED(1, 1);   //灯1为左边的灯
    			}
    		}
    		else 
    		{
    			Delay(5000);
    			//CTL_LED(1, 0);     //若数据发送失败，点亮led灯1
    		}
    	}
    */	
    }