STM32基于HAL库W25Q128驱动程序

柔情只为你懂 2022-10-19 04:21 333阅读 0赞

# STM32基于HAL库W25Q128驱动程序 #

--------------------

**在头文件中简单修改一下片选引脚IO即可使用。**

--------------------

### 源文件 ###

/** * @file w25qxx.c * * @brief Create by AnKun on 2020/6/18 * */
    
    #include "w25qxx.h"
    #include "spi.h"
    
    uint16_t W25QXX_TYPE = 0;
    uint32_t W25QXX_SIZE = 0;
    uint8_t  W25QXX_UID[8];
    
    static void delay_us(uint32_t us)
    { 
        uint32_t delay = (HAL_RCC_GetHCLKFreq() / 4000000 * us);
        while (delay--)
        { 
            ;
        }
    }
    
    //SPI读写一个字节
    //TxData:要写入的字节
    //返回值:读取到的字节
    static uint8_t W25QXX_SPI_ReadWriteByte(uint8_t TxData)
    { 
    	uint8_t RxData = 0X00;
    	if(HAL_SPI_TransmitReceive(W25QXX_SPI_Handle, &TxData, &RxData, 1, 10) != HAL_OK)
    	{ 
    		RxData = 0XFF;
    	}
    	return RxData;
    }
    
    //4Kbytes为一个Sector
    //16个扇区为1个Block
    //W25Q128
    //容量为16M字节,共有128个Block,4096个Sector
    
    //初始化SPI FLASH的IO口
    int W25QXX_Init(void)
    { 
    	MX_SPI1_Init();
        W25QXX_CS_L(); /* 拉低选中 */
        W25QXX_SPI_ReadWriteByte(0XFF);
        W25QXX_CS_H(); /* 拉高取消 */
        W25QXX_TYPE = W25QXX_ReadID();          // 读取FLASH ID.
    	W25QXX_SIZE = W25QXX_ReadCapacity();    // 读取容量
    	W25QXX_ReadUniqueID(W25QXX_UID);        // 读取唯一ID
    	if((W25QXX_TYPE & 0XEF00) != 0XEF00)
    	{ 
    		return -1;
    	}
    	return 0;
    }
    
    //读取W25QXX的状态寄存器
    //BIT7 6 5 4 3 2 1 0
    //SPR RV TB BP2 BP1 BP0 WEL BUSY
    //SPR:默认0,状态寄存器保护位,配合WP使用
    //TB,BP2,BP1,BP0:FLASH区域写保护设置
    //WEL:写使能锁定
    //BUSY:忙标记位(1,忙;0,空闲)
    //默认:0x00
    uint8_t W25QXX_ReadSR(void)
    { 
        uint8_t byte = 0;
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_ReadStatusReg); //发送读取状态寄存器命令
        byte = W25QXX_SPI_ReadWriteByte(0Xff);          //读取一个字节
        W25QXX_CS_H();  //取消片选
        return byte;
    }
    //写W25QXX状态寄存器
    //只有SPR,TB,BP2,BP1,BP0(bit 7,5,4,3,2)可以写!!!
    void W25QXX_Write_SR(uint8_t sr)
    { 
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_WriteStatusReg);                 //发送写取状态寄存器命令
        W25QXX_SPI_ReadWriteByte(sr);               	//写入一个字节
        W25QXX_CS_H();  //取消片选
    }
    //W25QXX写使能
    //将WEL置位
    void W25QXX_Write_Enable(void)
    { 
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_WriteEnable); 	//发送写使能
        W25QXX_CS_H();  //取消片选
    }
    //W25QXX写禁止
    //将WEL清零
    void W25QXX_Write_Disable(void)
    { 
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_WriteDisable);  //发送写禁止指令
        W25QXX_CS_H();  //取消片选
    }
    //读取芯片ID
    //返回值如下:
    //0XEF13,表示芯片型号为W25Q80
    //0XEF14,表示芯片型号为W25Q16
    //0XEF15,表示芯片型号为W25Q32
    //0XEF16,表示芯片型号为W25Q64
    //0XEF17,表示芯片型号为W25Q128
    uint16_t W25QXX_ReadID(void)
    { 
        uint16_t Temp = 0;
        W25QXX_CS_L();
        W25QXX_SPI_ReadWriteByte(0x90);                            //发送读取ID命令
        W25QXX_SPI_ReadWriteByte(0x00);
        W25QXX_SPI_ReadWriteByte(0x00);
        W25QXX_SPI_ReadWriteByte(0x00);
        Temp |= W25QXX_SPI_ReadWriteByte(0xFF) << 8;
        Temp |= W25QXX_SPI_ReadWriteByte(0xFF);
        W25QXX_CS_H();
        return Temp;
    }
    
    uint32_t W25QXX_ReadCapacity(void)
    { 
    	int i = 0;
    	uint8_t arr[4] = { 0,0,0,0};
        W25QXX_CS_L();
        W25QXX_SPI_ReadWriteByte(0x5A);
        W25QXX_SPI_ReadWriteByte(0x00);
        W25QXX_SPI_ReadWriteByte(0x00);
        W25QXX_SPI_ReadWriteByte(0x84);
    	W25QXX_SPI_ReadWriteByte(0x00);
    	for(i = 0; i < sizeof(arr); i++)
    	{ 
    		arr[i] = W25QXX_SPI_ReadWriteByte(0xFF);
    	}
        W25QXX_CS_H();
        return ((((*(uint32_t *)arr)) + 1) >> 3);
    }
    
    void W25QXX_ReadUniqueID(uint8_t UID[8])
    { 
    	int i = 0;
    	W25QXX_CS_L();
        W25QXX_SPI_ReadWriteByte(0x4B);
        W25QXX_SPI_ReadWriteByte(0x00);
        W25QXX_SPI_ReadWriteByte(0x00);
        W25QXX_SPI_ReadWriteByte(0x00);
    	W25QXX_SPI_ReadWriteByte(0x00);
        for(i = 0; i < 8; i++)
    	{ 
    		UID[i] = W25QXX_SPI_ReadWriteByte(0xFF);
    	}
    	W25QXX_CS_H();
    }
    
    //读取SPI FLASH
    //在指定地址开始读取指定长度的数据
    //pBuffer:数据存储区
    //ReadAddr:开始读取的地址(24bit)
    //NumByteToRead:要读取的字节数(最大65535)
    void W25QXX_Read(uint8_t *pBuffer, uint32_t ReadAddr, uint16_t NumByteToRead)
    { 
        uint16_t i;
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_ReadData);         	//发送读取命令
        W25QXX_SPI_ReadWriteByte((uint8_t)((ReadAddr) >> 16));  	//发送24bit地址
        W25QXX_SPI_ReadWriteByte((uint8_t)((ReadAddr) >> 8));
        W25QXX_SPI_ReadWriteByte((uint8_t)ReadAddr);
        for (i = 0; i < NumByteToRead; i++)
        { 
            pBuffer[i] = W25QXX_SPI_ReadWriteByte(0XFF);   	//循环读数
        }
        W25QXX_CS_H();
    }
    //SPI在一页(0~65535)内写入少于256个字节的数据
    //在指定地址开始写入最大256字节的数据
    //pBuffer:数据存储区
    //WriteAddr:开始写入的地址(24bit)
    //NumByteToWrite:要写入的字节数(最大256),该数不应该超过该页的剩余字节数!!!
    void W25QXX_Write_Page(uint8_t *pBuffer, uint32_t WriteAddr, uint16_t NumByteToWrite)
    { 
        uint16_t i;
        W25QXX_Write_Enable();                  	//SET WEL
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_PageProgram);      	//发送写页命令
        W25QXX_SPI_ReadWriteByte((uint8_t)((WriteAddr) >> 16)); 	//发送24bit地址
        W25QXX_SPI_ReadWriteByte((uint8_t)((WriteAddr) >> 8));
        W25QXX_SPI_ReadWriteByte((uint8_t)WriteAddr);
        for (i = 0; i < NumByteToWrite; i++)
            W25QXX_SPI_ReadWriteByte(pBuffer[i]); //循环写数
        W25QXX_CS_H();  //取消片选
        W25QXX_Wait_Busy();					   		//等待写入结束
    }
    //无检验写SPI FLASH
    //必须确保所写的地址范围内的数据全部为0XFF,否则在非0XFF处写入的数据将失败!
    //具有自动换页功能
    //在指定地址开始写入指定长度的数据,但是要确保地址不越界!
    //pBuffer:数据存储区
    //WriteAddr:开始写入的地址(24bit)
    //NumByteToWrite:要写入的字节数(最大65535)
    //CHECK OK
    void W25QXX_Write_NoCheck(uint8_t *pBuffer, uint32_t WriteAddr, uint16_t NumByteToWrite)
    { 
        uint16_t pageremain;
        pageremain = 256 - WriteAddr % 256; //单页剩余的字节数
        if (NumByteToWrite <= pageremain)
            pageremain = NumByteToWrite; //不大于256个字节
        while (1)
        { 
            W25QXX_Write_Page(pBuffer, WriteAddr, pageremain);
            if (NumByteToWrite == pageremain)
                break; //写入结束了
            else //NumByteToWrite>pageremain
            { 
                pBuffer += pageremain;
                WriteAddr += pageremain;
    
                NumByteToWrite -= pageremain;			  //减去已经写入了的字节数
                if (NumByteToWrite > 256)
                    pageremain = 256; //一次可以写入256个字节
                else
                    pageremain = NumByteToWrite; 	  //不够256个字节了
            }
        };
    }
    //写SPI FLASH
    //在指定地址开始写入指定长度的数据
    //该函数带擦除操作!
    //pBuffer:数据存储区
    //WriteAddr:开始写入的地址(24bit)
    //NumByteToWrite:要写入的字节数(最大65535)
    uint8_t W25QXX_BUFFER[4096];
    void W25QXX_Write(uint8_t *pBuffer, uint32_t WriteAddr, uint16_t NumByteToWrite)
    { 
        uint32_t secpos;
        uint16_t secoff;
        uint16_t secremain;
        uint16_t i;
        uint8_t *W25QXX_BUF;
        W25QXX_BUF = W25QXX_BUFFER;
        secpos = WriteAddr / 4096; 	  //扇区地址
        secoff = WriteAddr % 4096; 	  //在扇区内的偏移
        secremain = 4096 - secoff; 	  //扇区剩余空间大小
        if (NumByteToWrite <= secremain)
            secremain = NumByteToWrite; 	  //不大于4096个字节
        while (1)
        { 
            W25QXX_Read(W25QXX_BUF, secpos * 4096, 4096); 	  //读出整个扇区的内容
            for (i = 0; i < secremain; i++) //校验数据
            { 
                if (W25QXX_BUF[secoff + i] != 0XFF)
                    break; //需要擦除
            }
            if (i < secremain) //需要擦除
            { 
                W25QXX_Erase_Sector(secpos);		//擦除这个扇区
                for (i = 0; i < secremain; i++)	   		//复制
                { 
                    W25QXX_BUF[i + secoff] = pBuffer[i];
                }
                W25QXX_Write_NoCheck(W25QXX_BUF, secpos * 4096, 4096);	   	//写入整个扇区
    
            }
            else
                W25QXX_Write_NoCheck(pBuffer, WriteAddr, secremain); //写已经擦除了的,直接写入扇区剩余区间.
            if (NumByteToWrite == secremain)
                break; //写入结束了
            else //写入未结束
            { 
                secpos++; //扇区地址增1
                secoff = 0; //偏移位置为0
    
                pBuffer += secremain;  				//指针偏移
                WriteAddr += secremain;				//写地址偏移
                NumByteToWrite -= secremain;			//字节数递减
                if (NumByteToWrite > 4096)
                    secremain = 4096;			//下一个扇区还是写不完
                else
                    secremain = NumByteToWrite;		//下一个扇区可以写完了
            }
        };
    }
    
    //擦除整个芯片
    //等待时间超长...
    void W25QXX_Erase_Chip(void)
    { 
        W25QXX_Write_Enable();                 	 	//SET WEL
        W25QXX_Wait_Busy();
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_ChipErase);        	//发送片擦除命令
        W25QXX_CS_H();  //取消片选
        W25QXX_Wait_Busy();   				   		//等待芯片擦除结束
    }
    //擦除一个扇区
    //Dst_Addr:扇区地址 根据实际容量设置
    //擦除一个山区的最少时间:150ms
    void W25QXX_Erase_Sector(uint32_t Dst_Addr)
    { 
        //监视falsh擦除情况,测试用
        Dst_Addr *= 4096;
        W25QXX_Write_Enable();                  	//SET WEL
        W25QXX_Wait_Busy();
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_SectorErase);      	//发送扇区擦除指令
        W25QXX_SPI_ReadWriteByte((uint8_t)((Dst_Addr) >> 16));  	//发送24bit地址
        W25QXX_SPI_ReadWriteByte((uint8_t)((Dst_Addr) >> 8));
        W25QXX_SPI_ReadWriteByte((uint8_t)Dst_Addr);
        W25QXX_CS_H();  //取消片选
        W25QXX_Wait_Busy();   				   		//等待擦除完成
    }
    //等待空闲
    void W25QXX_Wait_Busy(void)
    { 
        while ((W25QXX_ReadSR() & 0x01) == 0x01);  		// 等待BUSY位清空
    }
    //进入掉电模式
    void W25QXX_PowerDown(void)
    { 
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_PowerDown);        //发送掉电命令
        W25QXX_CS_H();  //取消片选
        delay_us(3);                               //等待TPD
    }
    //唤醒
    void W25QXX_WAKEUP(void)
    { 
        W25QXX_CS_L(); //使能器件
        W25QXX_SPI_ReadWriteByte(W25X_ReleasePowerDown); // send W25X_PowerDown command 0xAB
        W25QXX_CS_H();  //取消片选
        delay_us(3);                            	//等待TRES1
    }

### 头文件 ###

#ifndef __W25QXX_H
    #define __W25QXX_H
    
    #include <main.h>
    
    #define W25QXX_SPI_Handle (&hspi1)
    
    //W25X系列/Q系列芯片列表
    //W25Q80 ID 0XEF13
    //W25Q16 ID 0XEF14
    //W25Q32 ID 0XEF15
    //W25Q64 ID 0XEF16
    //W25Q128 ID 0XEF17
    #define W25Q80 0XEF13
    #define W25Q16 0XEF14
    #define W25Q32 0XEF15
    #define W25Q64 0XEF16
    #define W25Q128 0XEF17
    
    
    #define W25QXX_CS_L() HAL_GPIO_WritePin(W25QXX_CS_GPIO_Port, W25QXX_CS_Pin, GPIO_PIN_RESET)
    #define W25QXX_CS_H() HAL_GPIO_WritePin(W25QXX_CS_GPIO_Port, W25QXX_CS_Pin, GPIO_PIN_SET)
    
    
    extern uint16_t W25QXX_TYPE;
    extern uint32_t W25QXX_SIZE;
    extern uint8_t  W25QXX_UID[8];
    
    
    //
    //指令表
    #define W25X_WriteEnable 0x06
    #define W25X_WriteDisable 0x04
    #define W25X_ReadStatusReg 0x05
    #define W25X_WriteStatusReg 0x01
    #define W25X_ReadData 0x03
    #define W25X_FastReadData 0x0B
    #define W25X_FastReadDual 0x3B
    #define W25X_PageProgram 0x02
    #define W25X_BlockErase 0xD8
    #define W25X_SectorErase 0x20
    #define W25X_ChipErase 0xC7
    #define W25X_PowerDown 0xB9
    #define W25X_ReleasePowerDown 0xAB
    #define W25X_DeviceID 0xAB
    #define W25X_ManufactDeviceID 0x90
    #define W25X_JedecDeviceID 0x9F
    
    int W25QXX_Init(void);
    void W25QXX_ReadUniqueID(uint8_t UID[8]);
    uint16_t  W25QXX_ReadID(void);  	    		//读取FLASH ID
    uint8_t	 W25QXX_ReadSR(void);        		//读取状态寄存器
    void W25QXX_Write_SR(uint8_t sr);  			//写状态寄存器
    void W25QXX_Write_Enable(void);  		//写使能
    void W25QXX_Write_Disable(void);		//写保护
    void W25QXX_Write_NoCheck(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite);
    void W25QXX_Read(uint8_t* pBuffer,uint32_t ReadAddr,uint16_t NumByteToRead);   //读取flash
    void W25QXX_Write(uint8_t* pBuffer,uint32_t WriteAddr,uint16_t NumByteToWrite);//写入flash
    void W25QXX_Erase_Chip(void);    	  	//整片擦除
    void W25QXX_Erase_Sector(uint32_t Dst_Addr);	//扇区擦除
    void W25QXX_Wait_Busy(void);           	//等待空闲
    void W25QXX_PowerDown(void);        	//进入掉电模式
    void W25QXX_WAKEUP(void);				//唤醒
    uint32_t W25QXX_ReadCapacity(void);
    
    #endif