svn配置

秒速五厘米 2022-07-11 16:04 189阅读 0赞

# svn配置路径配置 #

> 注意，在配置过程中，一般需要先用admin(管理员用户先进行配置进入后**创建多个文件夹**分别对应如：php, android … **授权对应的路径**)，这样才能在后续配置路径中可用。如果不是， 就会在checkout中出现如下错误:

URL 'svn://xxx.xx.xxx.xxx:xxxx/php/' doesn't exist

### 代码块\[文件夹/conf/authz\] (授权配置) ###

admin=test
    android=test2   
    php=test3
    
    [/]
    @admin=rw  //读写 管理员权限
    [/php]     //php php用户群权限 注意:必须先用admin用户创建总文件夹下的php目录才能成功checkout
    @php=rw
    [/android]  //安卓用户群权限 注意:必须先用admin用户创建总文件夹下的android目录才能成功checkout
    @android=rw

### 代码块\[文件夹/conf/passwd\] (用户名密码配置) ###

test=123456
    test2=123456
    test3=123456

### 代码块\[文件夹/conf/svnserve\] (svn服务配置) ###

### This file controls the configuration of the svnserve daemon, if you
    ### use it to allow access to this repository.  (If you only allow
    ### access through http: and/or file: URLs, then this file is
    ### irrelevant.)
    
    ### Visit http://subversion.tigris.org/ for more information.
    
    [general]
    ### These options control access to the repository for unauthenticated
    ### and authenticated users.  Valid values are "write", "read",
    ### and "none".  The sample settings below are the defaults.
    anon-access = none           //这里将###去掉表示启用代码, 注意如果想复制这一块请将所有'//'后的注释删除
    auth-access = write          //这里将###去掉
    ### The password-db option controls the location of the password
    ### database file.  Unless you specify a path starting with a /,
    ### the file's location is relative to the directory containing
    ### this configuration file.
    ### If SASL is enabled (see below), this file will NOT be used.
    ### Uncomment the line below to use the default password file.
    password-db = passwd          //这里将###去掉
    ### The authz-db option controls the location of the authorization
    ### rules for path-based access control.  Unless you specify a path
    ### starting with a /, the file's location is relative to the the
    ### directory containing this file.  If you don't specify an
    ### authz-db, no path-based access control is done.
    ### Uncomment the line below to use the default authorization file.
    authz-db = authz                //这里将###去掉
    ### This option specifies the authentication realm of the repository.
    ### If two repositories have the same authentication realm, they should
    ### have the same password database, and vice versa.  The default realm
    ### is repository's uuid.
    realm = My First Repository Test 
    
    [sasl]
    ### This option specifies whether you want to use the Cyrus SASL
    ### library for authentication. Default is false.
    ### This section will be ignored if svnserve is not built with Cyrus
    ### SASL support; to check, run 'svnserve --version' and look for a line
    ### reading 'Cyrus SASL authentication is available.'
    # use-sasl = true
    ### These options specify the desired strength of the security layer
    ### that you want SASL to provide. 0 means no encryption, 1 means
    ### integrity-checking only, values larger than 1 are correlated
    ### to the effective key length for encryption (e.g. 128 means 128-bit
    ### encryption). The values below are the defaults.
    # min-encryption = 0
    # max-encryption = 256

### 启用svn ###

$ svnserve -d -r [接文件夹路径] -listen-port [端口]

### svn输出 svncheckout ###

url: svn://xxx.xx.xxx.xxx:xxxx/php/  //即可获取php文件夹下的所有内容
    url: svn://xxx.xx.xxx.xxx:xxxx/android/  //即可获取android文件夹下的所有内容