SIM900 GPRS

ゝ一纸荒年。 2021-12-22 13:51 196阅读 0赞

#include <BlynkSimpleUserDefined.h>
    #include <SoftwareSerial.h>
    
    // SIM900 Shield Serial Pins
    SoftwareSerial SIM900(7, 8);
    
    // You should get Auth Token in the Blynk App.
    // Go to the Project Settings (nut icon).
    char auth[] = "4fadeMYTOKENee6cc96eded52d";
    #define ip_address "AT+CIPSTART=\"TCP\",\"8.8.8.8\",\"8442\""
    
    bool connected = false;
    
    // This function is used by Blynk to receive data
    size_t BlynkStreamRead(void* buf, size_t len)
    {
      return Serial.readBytes((byte*)buf, len);
    }
    
    // This function is used by Blynk to send data
    size_t BlynkStreamWrite(const void* buf, size_t len)
    {
      return Serial.write((byte*)buf, len);
    }
    
    void setup()
    {
      // Setup your connection here.
      
      pinMode(9, OUTPUT);
      Serial.begin(19200); // for serial monitor
      Serial.println("Powering on GPRS Shield.");
      SIM900.begin(19200); // Serial for GSM shield
      SIM900poweron();  // turn on shield
      
      sendCommand("AT", "OK", 1000);     //Wake up modem with an AT command
      if(sendCommand("AT", "OK", 1000) == 1){
        Serial.println("SIM900 started");
      }
      
      gprs();
      
      Blynk.begin(auth);
    
      do {
        connected = Blynk.connect();
      } while (!connected);
    }
    
    void loop()
    {
      
      Blynk.run(); 
        // Make sure that Blynk.run() is called
      // only when the connection is established
      if (connected) {
        // Okay, handle Blynk protocol
        bool hasIncomingData = (Serial.available() > 0);
        // Tell Blynk if it has incoming data
        // (this allows to skip unneeded BlynkStreamRead calls)
        if (!Blynk.run(hasIncomingData)) {
          // Error happened. No action for serial.
        }
      }
    }
    
    void gprs()
    {
      //Wake up modem with two AT commands
      sendCommand("AT", "OK", 1000);
      sendCommand("AT", "OK", 2000);
      sendCommand("AT+CIPSHUT", "SHUT OK", 2000);
      // Check if it's currently registered network
      if(sendCommand("AT+CREG?","+CREG: 0,1",2000)){ 
        Serial.println("Connected to the home cell network");
      }
      else{
        Serial.println("Not connected to home cell network");
        delay(10000);
      }
      
      Serial.println("Attaching to Packet Service");
      if(sendCommand("AT+CGATT=1","OK",3000)){ 
        Serial.println("Attached to Packet Service");
      }
      else{
        Serial.println("Unable to attach to Packet Service");
        delay(10000);
     }
    Serial.println("Setting APN");
    if(sendCommand("AT+CSTT=\"epc.tmobile.com\"","OK",3000)){ 
        Serial.println("APN Set");
      }
      else{
        Serial.println("Unable to set APN");
        delay(10000);
       }
    Serial.println("Starting GPRS Connection");
    if(sendCommand("AT+CIICR","OK",5000)){ 
        Serial.println("GPRS Connection Established");
        delay(1000);
        sendCommand("AT+CIFSR", "OK", 1000);
      }
      else{
        Serial.println("Unable to start GPRS connection");
        delay(10000);
     }
     Serial.println("Establishing TCP Connection");
    
     SIM900.println(ip_address);
     delay(1000);
     Serial.println("Connected to server");
      
       
    }
    
    void SIM900poweron()
    // Software equivalent of pressing the GSM shield "power" button
    {
      //Wake up modem with an AT command
      sendCommand("AT", "OK", 1000);
      if(sendCommand("AT", "OK", 2000) == 0){
        digitalWrite(9, HIGH);
        delay(1000);
        digitalWrite(9, LOW);
        delay(7000);
      }
    
    }
    
    int sendCommand(char* ATcommand, char* expected_answer, unsigned int timeout){
    
        
        int answer=0;
        int responsePos=0;
        char response[100];
        unsigned long previous;
    
        memset(response, '\0', 100);    // Clears array
    
        delay(100);
    
        while( SIM900.available() > 0) SIM900.read();    // Clean the input buffer
    
        SIM900.println(ATcommand);    // Send the AT command 
    
    
        responsePos = 0;
        previous = millis();
    
        // this loop waits for the answer
        do{
            // if there are data in the UART input buffer, reads it and checks for the asnwer
            if(SIM900.available() != 0){    
                response[responsePos] = SIM900.read();
                responsePos++;
                // check if the desired answer is in the response of the module
                if (strstr(response, expected_answer) != NULL)    
                {
                  answer = 1;
                }
            }
            // Waits for the asnwer with time out
        }while((answer == 0) && ((millis() - previous) < timeout));    
        return answer;
    }

转载于:https://www.cnblogs.com/zany-hui/articles/6908603.html